Key takeaways
- Compare the best RV leveling blocks, from curved drive-on levelers to interlocking stacks, with lift ranges, weight ratings, and pack sizes explained.
The best RV leveling blocks for most campers are interlocking stacking blocks like the Tri-Lynx Lynx Levelers, which build a stepped ramp in one-inch increments and double as pads under jacks and stabilizers. If you would rather drive on and stop at the exact height you need, a curved leveler such as the Andersen Camper Leveler or the Beech Lane Camper Leveler gives continuous lift from 1/2 inch to 4 inches with no stacking or guessing. The right choice comes down to how much lift your campsites usually demand, how heavy your rig is, and whether you want one kit that also works under tongue jacks and stabilizer feet.
As an Amazon Associate, we earn from qualifying purchases.
Table of Contents
- What RV Leveling Blocks Actually Do
- How to Choose the Right Leveling Blocks
- 1. Andersen Hitches 3604 Camper Leveler 2-Pack
- 2. Beech Lane Camper Leveler 2 Pack with Carrying Bag
- 3. Tri-Lynx 00015 Lynx Levelers 10-Pack
- 4. Camco FasTen Leveling Blocks 10-Pack
- 5. Valterra A10-0918 Stackers 10-Pack
- Frequently Asked Questions
- Conclusion
- Product and ASIN Reference
What RV Leveling Blocks Actually Do
Leveling blocks solve side-to-side slope. Most campsites are not flat, and an RV that leans is more than an annoyance: absorption refrigerators need to sit close to level to circulate properly, doors swing on their own, water pools at one end of the shower, and sleeping on a tilt gets old fast. Blocks go under the tires on the low side of the rig and raise that side until the trailer sits level. Front-to-back leveling is handled separately by the tongue jack on a travel trailer or the landing gear on a fifth wheel, so blocks only need to correct the side-to-side difference.
There are two families of products. Stacking blocks are flat, interlocking squares that build up like toy bricks, usually adding one inch of height per layer, and you drive up a stepped pyramid you assemble on the ground. Curved levelers are single wedge-shaped ramps: you place one in front of each low-side tire, drive forward slowly, and stop the moment the bubble reads level, which gives you any height within the ramp’s range rather than fixed one-inch steps. Both appear in the picks below, because the better system depends on your rig and your patience at the end of a long driving day.
How to Choose the Right Leveling Blocks
Start with lift range. Stacking blocks add height in fixed increments, so a ten-pack split between two tires gives you up to about five inches under one tire if you build a single pyramid, less if you split the stack. Curved levelers top out at four inches but hit every height below that exactly. If your favorite sites are badly sloped, blocks give more total lift; if they are only slightly off, a curved leveler is faster and more precise.
Next, check the weight rating against your rig’s gross vehicle weight, and remember the rating assumes firm, level ground. Soft sand, mud, and sharp gravel can crack blocks that would be fine on pavement, which is why several makers include rubber mats that spread the load and stop the leveler skating forward as the tire climbs.
Tire fit matters with curved levelers. Andersen rates its leveler for tires up to 32 inches in diameter, and closely spaced tandem axles can be a problem for any long ramp: the ramp under the front tire may need trimming so the rear tire does not climb it too. Stacking blocks avoid that issue entirely because the pyramid is only as long as you build it.
Finally, think about the second job. Blocks that also work under stabilizer jacks and tongue jacks earn their storage space twice, and a ten-pack can be split between tires and jacks on the same trip. A carry bag or locking handle sounds minor until you are loading wet, muddy blocks into a pass-through compartment.
1. Andersen Hitches 3604 Camper Leveler 2-Pack
Tier: Premium
The Andersen Camper Leveler is the product that made curved levelers mainstream, and the 3604 2-Pack with rubber mats and a carry bag is the version to buy for a tandem-axle trailer. Each leveler is a solid curved ramp: place it in front of a low-side tire, drive forward slowly while a partner watches the level, and stop anywhere between 1/2 inch and 4 inches of lift. The matching chock then slides under the raised leveler to lock the tire in place. Because the lift is continuous, you never end up half an inch too high or too low the way you can with one-inch block increments.
Andersen rates the leveler for trailers up to 30,000 pounds and tires up to 32 inches in diameter, which covers the large majority of travel trailers and fifth wheels. The included rubber mats go under the levelers on slick surfaces such as wet pavement or smooth concrete, where a bare ramp can otherwise slide as the tire starts to climb. For dual-axle rigs with tight spacing, Andersen notes the leveler can be trimmed so it clears the second tire. Everything packs into the included bag, and the two-pack format means both low-side tires on a tandem setup get their own ramp.
Specs
- Type: Curved drive-on leveler with chock
- Lift range: 1/2 inch to 4 inches, continuous
- Weight rating: Trailers up to 30,000 pounds
- Tire fit: Up to 32 inches in diameter
- Kit contents: 2 levelers, 2 chocks, 2 rubber mats, carry bag
- Model: 3604 (3604-RTBA kit)
2. Beech Lane Camper Leveler 2 Pack with Carrying Bag
Tier: Premium
Beech Lane’s Camper Leveler follows the same curved-ramp idea as the Andersen and adds a few thoughtful upgrades. The levelers are molded from a high-performance nylon polymer rather than standard plastic, a material Beech Lane chose for structural load-bearing strength, and the company backs the set with a lifetime warranty. The rated capacity is 35,000 pounds, the highest of the curved levelers here, and the lift range matches the Andersen at any increment from 1/2 inch to 4 inches. A textured grid pattern on the ramp surface helps the tire grip as it climbs, which matters on wet grass and loose gravel.
The kit includes two curved levelers, two chocks, two separate rubber grip mats, and a carrying bag. The separate mats are a deliberate design choice: instead of rubber bonded to the ramp, you lay the mat down first, so there is nothing to tear off and the mat can be replaced on its own. Each leveler is roughly 6 inches wide, and like other curved ramps it can be trimmed to fit between closely spaced tandem tires. At 16.8 pounds for the packaged set, it is heavier than a bag of stacking blocks, which is the trade for the solid nylon construction.
Specs
- Type: Curved drive-on leveler with chock
- Lift range: 1/2 inch to 4 inches, any increment
- Weight rating: Campers up to 35,000 pounds
- Material: High-performance nylon polymer
- Kit contents: 2 levelers, 2 chocks, 2 rubber grip mats, carrying bag
- Warranty: Lifetime warranty from the manufacturer
- Model: BL-115-SIZE
3. Tri-Lynx 00015 Lynx Levelers 10-Pack
Tier: Mid-range
Lynx Levelers are the original interlocking leveling blocks and still the most versatile option in this roundup. Each orange block measures 8.5 by 8.5 inches and adds one inch of lift, and the blocks lock together on all four sides, so the stepped pyramid you build does not spread apart as the tire climbs it. Tri-Lynx rates the system for up to 40,000 pounds and recommends stacking no more than five blocks high in a single ramp, which means one ten-pack builds two ramps of useful height or one taller pyramid with blocks left over for the jacks.
That second use is the real reason to pick Lynx over a curved ramp. The same blocks work under stabilizer jacks, tongue jacks, and leveling jacks, and the system accepts accessories such as caps that create a flat top surface for jack feet. The ten-pack weighs 7.5 pounds, stores in the included nylon bag, and is made in the USA. Tri-Lynx covers the set with a 10-year warranty, the longest stated coverage among the stacking blocks here. If you level on varied ground and want one kit that handles tires and jacks alike, this is the default recommendation.
Specs
- Type: Interlocking stacking blocks
- Lift: 1 inch per block; maker recommends no more than 5 blocks high per ramp
- Block size: 8.5 x 8.5 inches
- Weight rating: Up to 40,000 pounds
- Kit contents: 10 blocks, nylon storage bag
- Set weight: 7.5 pounds
- Warranty: 10-year manufacturer warranty
- Model: 00015
4. Camco FasTen Leveling Blocks 10-Pack
Tier: Budget
Camco’s FasTen blocks do the same interlocking job as the Lynx set at a friendlier tier, with one clever storage trick: the carrying handle threads through the stacked blocks and twists to lock them together, so the set travels as a single tidy unit with no separate bag to lose. Each block measures 8.5 by 8.5 by 1 inch and adds one inch of lift per layer, and Camco specifies a maximum stack height of 4.5 inches. The blocks are molded from UV-stabilized resin, which suits gear that lives in an outside compartment and spends its working life in the sun.
The FasTen set is aimed at single and double wheels and can also be used under hydraulic jacks, tongue jacks, and stabilizers. The open grid underside keeps each block light, at 8.5 pounds for the full ten-pack, though the same grid can pack with mud on soft ground and benefits from a quick rinse before storage. For lighter travel trailers and pop-up campers that rarely need more than a few inches of correction, this is the sensible budget pick; very heavy fifth wheels are better served by the higher-rated sets above.
Specs
- Type: Interlocking stacking blocks
- Lift: 1 inch per block; maximum stack height 4.5 inches
- Block size: 8.5 x 8.5 x 1 inch
- Material: UV-stabilized resin
- Kit contents: 10 blocks, twist-lock carrying handle
- Set weight: 8.5 pounds
- Model: 44512
5. Valterra A10-0918 Stackers 10-Pack
Tier: Budget
Valterra’s Stackers take a slightly different shape from the other blocks here. Each red pad measures approximately 8 by 10 by 1.5 inches, so a single layer already gives an inch and a half of lift, and the pads stack and lock together for more. Valterra and the Amazon listing rate the set at 40,000 pounds gross vehicle weight on firm, level ground, or 10,000 pounds per wheel, which is a strong rating for a budget set. The taller single-pad height also makes Stackers useful as jack stands and tongue wheel supports, the multi-use role Valterra designs them for.
The bright red color is a small but genuine advantage: pads are easy to spot in dirt and dusk light, and harder to leave behind at a campsite. A ten-pack gives enough pads to level one side of a tandem-axle trailer and still have pads for the stabilizers. As with every block here, the rating depends on firm ground; on soft surfaces, spread the load with a mat or board under the first layer.
Specs
- Type: Stacking leveling pads
- Lift: Approximately 1.5 inches per pad
- Pad size: Approximately 8 x 10 x 1.5 inches
- Weight rating: 40,000 pounds gross vehicle weight; 10,000 pounds per wheel
- Kit contents: 10 pads
- Uses: Leveling, jack stands, tongue wheel support
- Model: A10-0918
Frequently Asked Questions
How many leveling blocks does an RV need?
A single ten-pack is enough for most travel trailers: it builds two stepped ramps for the low-side tires of a tandem axle, or one ramp plus pads for the stabilizers on a single-axle trailer. Campers who regularly park on badly sloped sites, or who want blocks under both the tires and all four stabilizer jacks at once, should carry two sets. Curved levelers are sold per tire position, so a tandem-axle rig needs a two-pack.
Can leveling blocks be used under stabilizer jacks?
Yes, and that is one of the main advantages of stacking blocks over curved ramps. A flat block or a small stack under each stabilizer foot spreads the load, keeps the foot out of mud and gravel, and reduces how far the jack has to extend, which makes the trailer feel more solid. Just remember that stabilizers are not leveling jacks: level the trailer with blocks under the tires first, then set the stabilizers down onto their pads.
What is the difference between curved levelers and stacking blocks?
Curved levelers are solid ramps you drive onto, and they give continuous lift anywhere in their range, typically 1/2 inch to 4 inches, so they are fast and precise but work only under tires. Stacking blocks add lift in fixed steps and take longer to build, but they are cheaper, lighter, and can also go under jacks and stabilizers. Many campers carry blocks for versatility and add curved levelers later for speed.
How high can you stack RV leveling blocks?
Follow the limit the maker publishes for your set rather than a general rule. Tri-Lynx recommends no more than five Lynx blocks high in one ramp, and Camco sets a maximum stack height of 4.5 inches for the FasTen set. Build the stack as a stepped pyramid with each layer smaller than the one below it, keep the tire fully supported on the top layer, and never use blocks to lift a tire completely off the ground for tire changes or repairs.
Conclusion
For most campers, the Tri-Lynx Lynx Levelers 10-Pack is the buy: it is light, carries a 40,000-pound rating and a 10-year warranty, and the same blocks work under tires, jacks, and stabilizers. If speed and precision matter more, the Andersen 3604 2-Pack and the Beech Lane 2 Pack both deliver exact lift between 1/2 inch and 4 inches, with the Beech Lane offering the higher rating and a lifetime warranty. On a budget, the Camco FasTen adds a useful locking handle, while the Valterra Stackers give the most lift per layer and double as jack and tongue wheel pads. Match the rating to your rig’s gross weight, respect each maker’s stacking limit, and any of these five will end the sloped-campsite shuffle.
Related guides